How to Apply Clear Non-Slip Grip Spray for Long-Lasting Slip Resistance

How to Apply Clear Non-Slip Grip Spray for Long-Lasting Slip Resistance

How to Apply Clear Non-Slip Grip Spray for Long-Lasting Slip Resistance

Whether you're making a shower safer, adding traction to outdoor stairs, or protecting a slippery boat deck, proper application is the key to getting the best results from your Sticky Bee Grip Floor Safety Grip Spray.

Many people assume you can simply spray the surface and walk away. While our clear grip spray is incredibly easy to use, taking a few extra minutes to prepare the surface and apply multiple light coats will give you the strongest bond, the clearest finish, and the best slip resistance.

Step 1: Proper Surface Preparation

The most important part of any coating project is preparing the surface correctly.

Before spraying, make sure the surface is:

  • Completely clean
  • Completely dry
  • Free of dirt, grease, oils, waxes, and soap residue

If you're applying the coating inside a shower or bathtub, pay extra attention to removing soap scum and body oils. These contaminants can prevent the coating from bonding properly.

For glossy surfaces like sealed concrete, fiberglass, or aluminum, lightly scuffing the surface can improve adhesion and help create a more durable finish.

Step 2: Shake the Can Thoroughly

Before spraying:

  • Shake the can for at least one minute after the mixing ball begins to rattle.
  • Continue shaking occasionally during application.
  • Test the spray pattern on a piece of cardboard before coating your project.

This helps ensure the grip particles remain evenly suspended throughout the coating for a consistent finish.

Step 3: Apply Thin, Even Coats

For the best appearance and performance:

  • Hold the can approximately 12–15 inches from the surface.
  • Apply 2–3 light coats rather than one heavy coat.
  • Begin with a light mist coat.
  • Wait 15–20 minutes between coats.

Applying several light coats creates a more uniform texture while helping prevent runs and uneven buildup.

Step 4: Allow Proper Dry Time

Once the final coat has been applied:

  • The coating becomes dry to the touch in approximately 30 minutes.
  • Maximum durability and traction develop as the coating fully cures.

Avoid heavy traffic until the coating has had sufficient time to dry completely.

Common Application Mistakes

Most application issues can be avoided by following a few simple guidelines.

Runs or Drips

Usually caused by:

  • Spraying too close
  • Applying heavy coats

Solution: Use lighter coats while maintaining the recommended spray distance.

Rough or Uneven Texture

Usually caused by spraying too far away.

Solution: Stay within the recommended spray distance for an even finish.

Poor Adhesion

Usually caused by inadequate surface preparation.

Solution: Thoroughly clean the surface before applying the coating.

Clogged Spray Pattern

Usually caused by insufficient shaking.

Solution: Shake the can longer and test spray before applying.

Where Can You Use Sticky Bee Grip?

Sticky Bee Grip creates a durable, clear textured coating on many surfaces, including:

  • Shower floors
  • Bathtubs
  • Bathroom tile
  • Concrete
  • Pool decks
  • Stairs
  • Walkways
  • Boat decks
  • Wood
  • Fiberglass
  • Aluminum
  • Steel
  • Ramps

The clear finish helps preserve the appearance of the original surface while adding extra traction where it's needed most.

Pro Tips for Professional Results

For the best-looking finish:

  • Less is more—build traction gradually with multiple light coats.
  • Always test the product in a small, inconspicuous area first.
  • Remember that clear coatings won't hide scratches or surface imperfections, so proper preparation makes all the difference.

Stay Safe with Sticky Bee Grip

Slippery surfaces are one of the leading causes of household and workplace injuries. Whether you're protecting your family at home or improving safety in commercial spaces, Sticky Bee Grip Floor Safety Grip Spray offers an easy way to add long-lasting traction without changing the look of your surface.

With proper preparation, careful application, and a little patience during drying, you'll enjoy a durable, clear, slip-resistant finish that helps make every step more secure.





Back to blog